We ship worldwide!     Contact us : info@rev9autosport.com

We're sorry, our system cannot estimate the shipping either due to the quantity of items in cart or the country it's being shipped to!
close

Kansai Service

Grid  List 

per page
Set Descending Direction

9 Item(s)

  1. Kansai Service Center-Lower Brace Bar

    Kansai Service Center-Lower Brace Bar

    $549.99
    Fantastic center bracing kit made by Kansai Service of Japan for the ND (2016+) Miata. This kit expands on the idea of the normal brace bar by expanding the mounting points from 4 to 6! The kit is made from oval aluminum shafts for lightweight and strength. Replacing your normal brace with this one only adds about 600g to the cars weight and will noticeably affect handling. Learn More

  2. Kansai Service Fender Extensions

    Kansai Service Fender Extensions

    $374.99
    Small rear bumper garnish kit made by Kansai Service for the 2016+ ND MX-5. The extension kit installs in the rear fender well to give a slightly wider look from the rear. This part pairs very well the Kansai service’s side step kit, which creates a uniform look. NOTE: Installation of this part requires some cutting of the OEM body parts. Learn More

  3. Kansai Service Front Member Plate

    Kansai Service Front Member Plate

    $249.99
    Member reinforcement plates made by Kansai Service of Japan. These member plates are only 3.2mm in thickness and made of pressed steel. These plates will stiffen up the front of your vehicle for better handling! Learn More

  4. Kansai Service Front Short Diffusers

    Kansai Service Front Short Diffusers

    $449.99
    Front short lips designed by Kansai service for the ND (2016+) MX-5 Miata. Kansai service made this lip to exude a wider, sportier appearance when looked at from any angle. The lip protrudes just a touch past the OEM bumper to enhance the look of the roadster. Kansai service also sought to ensure that the lip is friendly for the road and to that end doesn’t extend far down so it’s less likely to scrape. Made of carbon fiber for both strength and low weight. Learn More

  5. Kansai Service Front Tower Bar

    Kansai Service Front Tower Bar

    $399.99
    Strong 4-point front strut bar bar made by Kansai Service of Japan for the ND (2016+) Miata. Kansai Service uses steel bases with Chromoly shafts to connect both sides of the vehicle together for greater handling ability. It only weights 3.58KG. Note: If your Miata is not equipped with a strut tower bar from the factory, an OEM kit is needed, part number #N244-56-35X. This is for the air cowl panel Learn More

  6. Kansai Service Front-Lower Brace Bar

    Kansai Service Front-Lower Brace Bar

    $159.99

    Front brace bar made by Kansai Service of Japan. This is the lower brace bar for the front of the ND (2016+) Miata and will go even further in tightening up your car. This bar is made of an aluminum oval shaft. Note that the Kansai Service Front Member Plates are REQUIRED to install this part.

    Learn More

  7. NOPRO Rear Spoiler For Miata MX5 MX-5 06-08 JDM Roadster : REV9 Autosport

    Kansai Service Rear Spoiler

    $699.99
    Rear lip spoiler made by Kansai Service of Japan for the ND (2016+) MX-5 Miata. Designed to strike a harmonious balance of proportions between the trunk lines and bottom section of the bumper, this lip will look great and give a little extra downforce! Made of wet carbon fiber and coated for UV protection for a long life span. Installs easily using double sided tape so you don’t have to drill in to your trunk! Learn More

  8. Kansai Service Rear Tower Bar

    Kansai Service Rear Tower Bar

    $239.99
    Rear strut tower bar made by Kansai Service. This part for the ND (2015+) Miata installs in the trunk to connect the left and right of the vehicle together. Kansai Service designed this bar to impact trunk space as little as possible while adding structural rigidity. Learn More

  9. Kansai Service Side Steps

    Kansai Service Side Steps

    Regular Price: $949.99

    Special Price $899.99

    Subtle side skirts made by Kansai Service for the 2016+ ND MX-5. Kansai service wanted to make body parts that not only looked awesome but also didn’t hinder street usability. These side steps have a fairly high ride height so that even if you have a lowered car, it will be less likely to scrape. The side steps flow well and follow the natural lines and bulges leading from the front to the rear of the vehicle for a racy appearance that just looks right. NOTE: In order to install these side steps, drilling in to the stock components is required. Learn More

Grid  List 

per page
Set Descending Direction

9 Item(s)